[原创]模具专业英语

zyc

<strong>模具专业英语</strong> <div style="PADDING-RIGHT: 0px; MARGIN-TOP: 10px; FONT-SIZE: 9pt; OVERFLOW-X: hidden; WIDTH: 97%; WORD-BREAK: break-all; TEXT-INDENT: 24px; LINE-HEIGHT: normal; HEIGHT: 250px; WORD-WRAP: break-word;"><span class="tpc_content"><font size="2">模具述语 <br/>一、入水：gate <br/>进入位：　gate location <br/>水口形式：gate type <br/>大水口：edge gate <br/>细水口： pin-point gate <br/>水口大小：gate size <br/>转水口：　switching runner/gate <br/>唧嘴口径：　sprue diameter <br/>二、流道: runner <br/>热流道：　hot runner,hot manifold <br/>热嘴冷流道: hot sprue/cold runner <br/>唧嘴直流: direct sprue gate <br/>圆形流道：round(full/half runner <br/>流道电脑分析：mold flow analysis <br/>流道平衡:runner balance <br/>热嘴：　hot sprue <br/>热流道板：hot manifold <br/>发热管：cartridge heater <br/>探针: thermocouples <br/>插头：　connector plug <br/>插座： connector socket <br/>密封/封料： seal <br/>三、运水：water line <br/>喉塞：line lpug <br/>喉管：tube <br/>塑胶管：plastic tube <br/>快速接头：jiffy quick connector plug/socker <br/>四、模具零件：　mold components <br/>三板模：3-plate mold <br/>二板模：2-plate mold <br/>边钉/导边：leader pin/guide pin <br/>边司/导套：bushing/guide bushing <br/>中托司：shoulder guide bushing <br/>中托边L：guide pin <br/>顶针板：ejector retainner plate <br/>托板：　support plate <br/>螺丝： screw <br/>管钉：dowel pin <br/>开模槽：ply bar scot <br/>内模管位：core/cavity inter-lock <br/>顶针：　ejector pin <br/>司筒：ejector sleeve <br/>司筒针：ejector pin <br/>推板：stripper plate <br/>缩呵：movable core,return core core puller <br/>扣机（尼龙拉勾）：nylon latch lock <br/>斜顶：lifter <br/>模胚（架）： mold base <br/>上内模：cavity insert <br/>下内模：core insert <br/>行位（滑块）： slide <br/>镶件：insert <br/>压座/斜鸡：wedge <br/>耐磨板/油板：wedge wear plate <br/>压条：plate &nbsp; &nbsp;<br/>撑头: support pillar <br/>唧嘴： sprue bushing <br/>挡板：stop plate <br/>定位圈：locating ring <br/>锁扣：latch <br/>扣鸡：parting lock set <br/>推杆：push bar <br/>栓打螺丝：S.H.S.B <br/>顶板：eracuretun <br/>活动臂：lever arm <br/>分流锥：spure sperader <br/>水口司:bush <br/>垃圾钉：stop pin <br/>隔片：buffle <br/>弹弓柱：spring rod <br/>弹弓:die spring <br/>中托司：ejector guide bush <br/>中托边：ejector guide pin <br/>镶针：pin <br/>销子：dowel pin <br/>波子弹弓：ball catch <br/>喉塞: pipe plug <br/>锁模块：lock plate <br/>斜顶：angle from pin <br/>斜顶杆：angle ejector rod <br/>尼龙拉勾：parting locks <br/>活动臂：lever arm <br/>复位键、提前回杆：early return bar <br/>气阀：valves <br/>斜导边：angle pin <br/>术语：terms <br/>承压平面平衡：parting surface support balance <br/>模排气：parting line venting <br/>回针碰料位：return pin and cavity interference <br/>模总高超出啤机规格：mold base shut hight <br/>顶针碰运水：water line interferes withejector pin <br/>料位出上/下模：part from cavith (core) side <br/>模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. <br/>不准用镶件： Do not use (core/cavity) insert <br/>用铍铜做镶件： use beryllium copper insert <br/>初步（正式）模图设计：preliinary (final) mold design <br/>反呵：reverse core <br/>弹弓压缩量：spring compressed length <br/>稳定性好：good stability,stable <br/>强度不够：insufficient rigidity <br/>均匀冷却：even cooling <br/>扣模：sticking <br/>热膨胀：thero expansion <br/>公差：tolorance <br/>铜公(电极）：copper electrode </font></span></div>

rivertang

好东西！谢谢分享·

chenchao11

多谢<strong>模具专业英语</strong>

zyc

<p>谢谢支持,大家也发一些上来...</p>

来来回回523

恩 好东东！

catforever

有音標就更好了～～～～～～～～～～～

kunpower

不错，是好东西，这么专业

zyhabc

楼主辛苦了

woba1982

我喜欢，自己复制以来，保存使用

roybooth

收藏了！！

jyi047

感謝樓主分享,收藏之.

1巧夺天工1

谢谢分享 楼主万福