(5)给大家一个模具分模练习！(做好有分加!)

dwlj2001

其实这样容易产生飞边

dwlj2001

我的<img src="attachments/dvbbs/20039313435696434.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039313435696434.jpg\');}" onmousewheel="return imgzoom(this);" alt="" /><img src="attachments/dvbbs/20039313441093748.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039313441093748.jpg\');}" onmousewheel="return imgzoom(this);" alt="" /><img src="attachments/dvbbs/20039313442693699.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039313442693699.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />

qwdzb

xuexi

寂寞工程师

不一定光是分型面问题，分型面有破面是决对分不了型的，它与你的结构设计也有关系，我就遇到了这么一个问题：后模斜顶的分型面做在与前模碰死的位置，结果也不能生成浇注件。在做PROE分模时，如果分不开的话，你第一步就应该去检查分型面与产品的面是否脱离，特别是进行小面合并时，最容易出现的问题，此时你可以不用原分型面分模，重新复制分型面的分割部分的曲面，不要复制产品部分的分型面，然后用新的面分模一般就会成功的！

eee555

thanks

leprechaun

我是proe的初学者，现在还在学零件设计。这对我来说太难了点。

longzy91

<img src="attachments/dvbbs/20039916595395992.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20039916595395992.jpg\');}" onmousewheel="return imgzoom(this);" alt="" /><img src="attachments/dvbbs/200399170035232.jpg" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/200399170035232.jpg\');}" onmousewheel="return imgzoom(this);" alt="" />
给我也加分。

brant2000

对精度有多大要求？
应该不是很难

chenzhenmei

??
是还可以啦

eastsea

各位：你们是不是都有模具实际经验？

火星人

领教了

韩萧

请教高手怎样分模啊！！！！！

cxj

不难啊

lyf2008

TOO EASY!

泽斌

有些压缩包我不能解压?为什么

Q.CHEN

不错，下回看我的！

vtee

动模用割好像不太好也