请教：1/4剖

JSJHJIA

我零件已装配好，如何进行1/4剖？要求：其中阀杆不剖。[em02][em00]

nixinming

使用配置就可以了

millcent77

晕

JSJHJIA

2楼 听不懂可否解释一下

深呼吸

传给图上来看看！

nixinming

<img src="attachments/dvbbs/20037120304470060.bmp" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20037120304470060.bmp\');}" onmousewheel="return imgzoom(this);" alt="" /><img src="attachments/dvbbs/20037120322412868.bmp" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20037120322412868.bmp\');}" onmousewheel="return imgzoom(this);" alt="" /><img src="attachments/dvbbs/20037120334535969.bmp" border="0" onload="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onmouseover="if(this.width>screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=\'hand\'; this.alt=\'Click here to open new window\nCTRL+Mouse wheel to zoom in/out\';}" onclick="if(!this.resized) {return true;} else {window.open(\'attachments/dvbbs/20037120334535969.bmp\');}" onmousewheel="return imgzoom(this);" alt="" />

JSJHJIA

大哥：可否将该模型给我研究研究？
1-4里具体配置如何？不懂

mpvr

nixinming大大的意思是..
利模型組態...開一新模組...將其所屬零件剖開...即可

zhchl

不知nixinming兄是否是利用装配图中的切割来实现的，在对其使用配置，对吗？

nixinming

装配体添加新的配置，产生一个新的装配体，在这个新配置的装配体中，将需要剖切的零件全部根据要求将其剖切，注意配置下面的选项选择为‘配置名称’。将默认装配体中的所有剖切全部压缩。这样就可以在装配体中剖与不剖之间来回切换了。另出二维工程图时也可切换。

[此贴子已经被作者于2003-7-2 18:20:59编辑过]

zhchl

看来想法是最重要的....

qliu1

3

JSJHJIA

可否将该模型上船，我还想看看o型圈如何装配
thanks

JSJHJIA

配置？不懂