模具论坛

 找回密码
 注册

扫一扫,微信登录

QQ登录

只需一步,快速开始

搜索
热搜: 冲压 注塑 求助
    回车查看更多
    论坛可能已存在您要发布的主题帖 关闭
      查看: 1058|回复: 0

      [分享]mold check list!!!

      [复制链接]
      发表于 2007-4-16 10:31:00 | 显示全部楼层 |阅读模式
      <p><font face="Tahoma">1. Wear plates to be XXXX thick.</font></p><p><font face="Tahoma">2.Pry slots between all molds base plates.</font></p><p><font face="Tahoma">3.All Lock SHCS to be accessible without disassembling mold base.</font></p><p><font face="Tahoma">4.Cover Cavity SHCS to be accessible without disassembling mold base.</font></p><p><font face="Tahoma">5.200 series and 300 series waterline fttting used?</font></p><p><font face="Tahoma">6.Spherical Radius in sprue bushing 1/2 or 3/4?</font></p><p><font face="Tahoma">7.clear spring pockets by and addtional .062" per side.</font></p><p><font face="Tahoma">8.clear all lock pockets by 0.005/side on the two non-fit sides.</font></p><p><font face="Tahoma">9.clear cavity pockets in base by 0.002/inch not to exceed .0015 over all.</font></p><p><font face="Tahoma">10.Do leader pins extend past cam pin?</font></p><p><font face="Tahoma">11.If possible does water come out the bottom of tool.</font></p><p><font face="Tahoma">12.are leader pins vented to atmosphere.</font></p><p><font face="Tahoma">13. Does mold base fit in priess (ti bar spacing)?</font></p><p><font face="Tahoma">14.dissimilar steel types for cvaity steel?</font></p><p><font face="Tahoma">15.Runner and gate type?</font></p><p><font face="Tahoma">16.was shrink added?</font></p><p><font face="Tahoma">17.Is there adequate EJ stroke?</font></p><p><font face="Tahoma">18.IS there enough slide stroke?</font></p><p><font face="Tahoma">19.Shipping strap taped holes not in handling holes?</font></p><p><font face="Tahoma">20.Handling holes?</font></p><p><font face="Tahoma">21.Support Pillars?</font></p><p><font face="Tahoma">22. Guided Ejection?</font></p><p><font face="Tahoma">23.Put "O" Ring grooves in mold base in at al possible.</font></p><p><font face="Tahoma">24.Does sprue need to be keyed?</font></p><p><font face="Tahoma">25.are there any keyed ejector pin needed?</font></p><p><font face="Tahoma">26.Does the runner have proper ejection?</font></p><p><font face="Tahoma">27.Thin switches and/or positive early return if EJ pin under slides.</font></p><p><font face="Tahoma">28.Positive slider stops?</font></p><p><font face="Tahoma">29.Progressive slide spring units?</font></p><p><font face="Tahoma">30.are knock out in and tap?</font></p><p><font face="Tahoma">31.Runner sucker?</font></p><p><font face="Tahoma">32 Are slide locks cleared for slide water fittings?</font></p><p>&nbsp;</p>
      您需要登录后才可以回帖 登录 | 注册

      本版积分规则

      关闭

      招聘信息 上一条 /5 下一条

      关闭

      求职信息 上一条 /5 下一条

      关闭

      技术求助 上一条 /5 下一条

      QQ|小黑屋|手机版|模具论坛 ( 浙ICP备15037217号 )

      GMT+8, 2025-7-22 13:24

      Powered by Discuz! X3.4

      © 2001-2013 Comsenz Inc.

      快速回复
      返回顶部
      返回列表
       
      客服电话:0577-61318188
      模具论坛交流群:
      模具论坛交流群
      工作时间:
      08:30-17:30